Maintenance Guide Maintenance guide
You can maintain yourself
We will guide you to how to attach and remove the door and drawer, how to adjust the door shift.
* The item where the playback mark is displayed will be described in the video, and when you click it, the video will flow. Please be careful about the volume.
How to adjust each part
- 扉の調整方法
- 扉のずれの原因や改善方法についてご紹介します。 >詳しくはこちら
- How to adjust the door
- Various causes can be considered for the difference in the height of the door, such as distortion of furniture itself caused by the slope of the floor and the weight of dishes, such as tableware.
-
- Cause (1) The door is not horizontal, but slope
- The four corners of the room are fixed on the base of the building, but other parts are often not fixed, so the floor is mostly inclined from the four corners of the room to the center.
When furniture is installed on a sloping floor, the furniture itself is distorted, and the height of the left and right doors may be shifted. - Cause (2) The weight of storage such as tableware
- If there is a difference in the weight of dishes, etc. on the left and right of the shelf, the center of gravity of the furniture is biased, causing distortion and shifting the height of the left and right doors.
-
- Solution / countermeasure method
- STEP: 1
- Compare the height of the left and right door
-
-
- STEP: 2
- In front of the lower door, a plate -shaped object※Insert between the furniture and the floor.
* Vertical 40-50 x 40-50mm, thickness of about 1-3mm
Example) If the left door is down, insert it under the left front corner (right.
-
* If there is still a difference in the height of the door, increase the thickness of the board. If it gets higher, reduce the thickness of the board and adjust it.
* By bending the paper several times, the thickness increases and can be used as a substitute for a board.
* Be sure to work with two or more people. -
-
- Cause ③ Insufficient adjustment of hinges
- At the beginning of the purchase, even if the hinge screws are tightly tightened, it may be loose as you use it. The loosening of the screws causes the height of the left and right doors to shift.
-
- Solution / countermeasure method
- Please make adjustments with reference to the following videos.
-
-
- Causes ④ Left and right hinges do not match
- It will be a bad product. I am very sorry.
Please contact the store you purchased.
- ベッドフレームの音鳴りの調整方法
- 音鳴りの原因や改善方法についてご紹介します。 >詳しくはこちら
- Bed frame
How to adjust the sound - The phenomenon that sounds when the members of the beds are rubbed with each other are called squeaking. Cooling can be improved by re -tightening the screws.
-
- Cause (1) Loose screws and nuts
- Loosiness in screws and nuts causes gaps in the members and members. If you use a bed in that state, the members and the members will rub each other and the sound will sound.
- Cause (2) Contact of members
- In the case of a bed where the floorboard and members are not fixed with screws, the sound will sound when the members and the members rub each other.
-
- If the sound comes from the bed itself
- Please re -tighten the screws and nuts of the bed itself.
- Put a cloth or felt between the members of the red circle below.
* Please re -tighten the screws regularly about once a month. If you continue to use it with a loose screw, it will cause the members to wobble, causing damage.
* Please use cotton cloth or felt.
* If you sandwich too thick cloth or felt, the members may not fit.
-
- Cause ③ Friction with the flooring floor
- The sound is heard when the floor member and the floor rub each other.
-
- When the sound is heard from the flooring floor and the legs of the bed
- Paste the felt etc. on the back of the legs of the bed of the red circle below.
How to attach and remove
Covering
others
- 床に付着したラグのベタつきの取り除き方
- 滑り止めによるベタつきの取り除き方や改善方法についてご紹介します。>詳しくはこちら
- The lag attached to the floor
How to remove sticky - If you continue to lay lags and mats in the same place for a long time, the temperature and humidity of the used environment may cause stickiness due to non -slip.
-
- Cause ① Continue to lay in the same place for a long time
- Cause ② Temperature, humidity, ultraviolet rays of the usage environment
- Causes ③ Decomposition / softening of non -slip ingredients
- The plasticizer of the flooring (additive that gives the flexibility contained in vinyl chloride or flooring wax) and the rubber non -slip part occur, and the non -slip components are decomposed and softened.
-
- How to clean
- ① Use neutral detergent to reduce sticky adhesion.
- ② Remove the sticky with the friction of the eraser.
- ③ Wipe water and wipe off the neutral detergent and eraser.
- ④ Wipe off the thinned sticky again with a neutral detergent.
- ⑤ Finally, wipe dry and complete.
- Change the rug or mat laid around once a week and check the status of the floor. It is also important to clean it regularly.
* Depending on the material of the flooring, it may cause stains and discoloration and damage the floor. Try it in an inconspicuous place and check the compatibility between floor materials and neutral detergents.
Characteristics of wood and care
Characteristics of wood
-
Orc
The skin is a rough and hard wood that is rough.
The wood grain is clear, and the beautiful wood grain appears on the straight side.
It is known for the tiger spots called a tiger spots. -
Acacia wood
The feature is that the color of the material is different from white to tea toward the center.
The wood grain is almost straight, but sometimes intertwines, and it is an attractive accent along with the knots. -
Ratin wood
Collective term for coconut velvetous plants.
It is light, durable, hard to break, and is easy to process curve. -
Rubber material
A good feel, relatively uniform and calm wood grain.
As a result, the skin is easy to make the skin condition and a beautiful pattern.
It is an environment -friendly wood because it grows fast and can be cultivated in a short cycle. -
Walnut material
It is a woody and sticky wood.
Glossy with warm expression, beautiful luster when polished.
The more you use it, the more the taste will be. -
Beach wood
A fine, white, smooth wood grain.
It features a fine spots on the straight grain.
Because it is strong and elastic, it is also famous as a wood suitable for bending trees that draw a beautiful curve. -
Teak wood
Very hard wooden, less stretch and warpage, and smooth.
It is a wooden skin that has both simpleness and elegance, and the more you use it, the more the taste is.
Care for wood
- Please wipe it dry. If the dirt is noticeable, soak it in a neutral detergent that is more than 200 times thinner with lukewarm water, wipe it off with a tightly squeezed cloth, and then wipe it well. Finally, wipe dry. Do not use chemical rags.
Care for rattan material products
- Please wipe it dry. If the dirt is noticeable, soak it in a neutral detergent that is more than 200 times thinner with lukewarm water, wipe it off with a tightly squeezed cloth, and then wipe it well. Finally, wipe dry. Do not use chemical rags. Lightly apply the dust of the mesh and the bonded peals with a soft cloth or a soft brush of the hair tip.
Care for oil finish products
To wipe water, wipe it lightly with a tightly squeezed cloth and then wipe. We recommend that you apply a special oil once every six months as a guide.
Please use only the oil -finished product. It cannot be used for print plywood. The adday / KURT series is not established in the grain at the beginning of the delivery, so if you apply clear, the color will be lighter. If you want to use it, please use it after 3 months. Please read and use the handling of the oil and use the handling precautions described in the product label.
* Please try it in an inconspicuous area, such as the back of the top plate.
* If you leave it too much after painting, it will cause stickiness, so be sure to wipe it off after 5 to 10 minutes.
* For a deeper finish without unevenness, apply twice.
* In the case of twice, apply the first paint, dry it for 4 hours or more, and perform the second paint.
